945G-M3 MANUAL PDF

Be respectful, keep it civil and stay on topic. We delete comments that violate our policy , which we encourage you to read. Discussion threads can be closed at any time at our discretion. ECS G-M3 - 3.

Author:Tojaramar Tezilkree
Country:Madagascar
Language:English (Spanish)
Genre:Science
Published (Last):25 February 2008
Pages:306
PDF File Size:5.95 Mb
ePub File Size:4.14 Mb
ISBN:891-5-69507-371-5
Downloads:18223
Price:Free* [*Free Regsitration Required]
Uploader:Kajisar



Quick Links. Table of Contents. Neither this manual, nor any of the material contained herein, may be reproduced without written consent of the author. Version 3.

Page 6 Integrated Peripherals IRDA Infrared header 5. Page 12 Memo Introducing the Motherboard Page Checking Jumper Settings Do not over-tighten the screws as this can stress the motherboard. Checking Jumper Settings This section explains how to set jumpers for correct configuration of the motherboard.

Setting Jumpers Use the motherboard jumpers to set system configuration options. Jumpers with more than one pin are numbered. Pin 1 is labeled. If the clip of the cooling fan scrapes across the motherboard, you may cause serious damage to the motherboard or its components. Read and follow the instructions shown on the sticker on the CPU cap. The total memory capacity is 2 GB.

Page Expansion Slots Expansion Slots Installing Add-on Cards The slots on this motherboard are designed to hold expansion cards and connect them to the system bus. Page 21 Follow these instructions to install an add-on card: Remove a blanking plate from the system case corresponding to the slot you are going to use.

Install the edge connector of the add-on card into the expansion slot. Ensure that the edge connector is correctly seated in the slot. Secure the metal bracket of the card to the system case with a screw. It elimi- nates limitations of the current Parallel ATA interface. When your system is in a power-saving mode, any LAN signal automatically resumes the system.

Additionally, some computer cases have USB ports at the front of the case. If you have this kind of case, use auxiliary USB connector to connect the front-mounted ports to the motherboard. Page Installing A Floppy Diskette Drive Refer to the illustration below for proper installation: Attach either cable end to the connector on the motherboard. Attach the other cable end to the SATA hard drive.

Page 30 This motherboard may adopt 6-channel audio ports. Use the three audio ports to connect audio de- vices. The first jack is for stereo line-in signal. The second jack is for stereo line-out signal. The third jack is for microphone. Installing the Motherboard Page Connecting Case Components Connecting Case Components After you have installed the motherboard into a case, you can begin con- necting the motherboard components. Page Standard Cmos Features For the purpose of better product maintenance, the manufacture reserves the right to change the BIOS items presented in this manual.

If you are setting up a new hard disk drive that supports LBA mode, more than one line will appear in the parameter box. Page 40 TM2 Bus Ratio 0X This item represents the frequency bus ratio of the throttled performance state that will be initiated when the on-die sensor goes from not hot to hot.

Some high-end processors support L3. If the CPU do support L3, you may set this item to enable or disable. Leave this item at the default value for better performance. Do not reset this field from the default value specified by the system designer. Select Enabled to activate each channel separately. SPP allows data output only. When set to 0 zero for the day of the month, the alarm will power on your system every day at the specified time.

Page Frequency Control Shutdown Temperature Disabled Enables you to set the maximum temperature the system can reach before powering down. System Component Characteristics These fields provide you with information about the systems current operating status. You cannot make changes to these fields. The password typed now will clear any previously entered password from CMOS memory.

You will be asked to confirm the password. New BIOS provides support for new peripherals, improve- ments in performance, or fixes for known bugs. Below you can find a brief description of each software program, and the location for your motherboard version. Select from the menu which software you want to install. Page 59 Click Next. The following screen appears: Check the box next to the items you want to install. The default options are recommended.

Click Next run the Installation Wizard. An item installation screen appears: Follow the instructions on the screen to install the items. Drivers and software are automatically installed in sequence. DOC file in the root directory. This file contains the information needed to locate the drivers for your motherboard. Look for the chipset and motherboard model; then browse to the directory and path to begin installing the drivers.

Print page 1 Print document 60 pages. Cancel Delete. Sign In OR. Don't have an account? Sign up! Restore password. Upload from disk. Upload from URL.

LA TOUTE PREMIRE FOIS LAUREN STRASNICK PDF

ECS 945GCT-M3 Manual

.

KINDERTRANSPORT SCRIPT PDF

ECS 945G-M3(V3.0) instruction manual and user guide

.

Related Articles