The Bugera W guitar amp head can achieve the tone of a high power super lead amp and provide all the virile crunch you'll need to detonate the stage. Turning the Clean gain up the Clean gain gradually causes the amp to react like a non-master volume amp, and achieves a very natural sounding overdrive what is known as "Texas Clean. The Crunch setting is simply the clean channel with more gain from another 12AX7 to create the Rock 'n' Roll rhythm sound heard on your classic rock faves. The Lead channel is all about articulate gain and sustain.
|Published (Last):||11 December 2015|
|PDF File Size:||19.41 Mb|
|ePub File Size:||17.44 Mb|
|Price:||Free* [*Free Regsitration Required]|
Risk of death! High voltages of up to V DC may be present inside the casing for long periods after being disconnected from the mains. To avoid lethal electric shock, do not open the casing.
There are no user-serviceable components inside. Refer all maintenance to qualified service personnel. Remove the mains cable when the unit is not in use. WARNING: To eliminate the risk of fire and electric shock, do not expose this unit to rain or moisture and splashing or dripping liquid, which might enter the device. Do not place any objects filled with liquid, such as vases, on the unit. This symbol, wherever it appears, alerts you to the presence of uninsulated dangerous voltage inside the enclosure—voltage that may be sufficient to constitute a risk of shock.
This symbol, wherever it appears, alerts you to important operating and maintenance instructions in the accompanying literature. Please read the manual. Keep these instructions. Heed all warnings. Follow all instructions. Do not use this apparatus near water. Clean only with dry cloth. Do not block any ventilation openings. Do not install near any heat sources such as radiators, heat registers, stoves, or other apparatus including amplifiers that produce heat.
A polarized plug has two blades with one wider than the other. A grounding type plug has two blades and a third grounding prong. The wide blade or the third prong are provided for your safety.
If the provided plug does not fit into your outlet, consult an electrician for replacement of the obsolete outlet. Servicing is required when the apparatus has been damaged in any way, such as power supply cord or plug is damaged, liquid has been spilled or objects have fallen into the apparatus, the apparatus has been exposed to rain or moisture, does not operate normally, or has been dropped.
To reduce the risk of electric shock do not perform any servicing other than that contained in the operation instructions unless you are qualified to do so. During use, the valves get very hot and high surface temperatures may be reached at the rear of this unit. To avoid burning yourself, make all connections while the unit is still cold.
Observe the correct impedance for your loudspeaker and use the appropriate output socket. Always use loudspeaker cables for connection between the amplifier and the loudspeaker. Never use other types of cable, like instrument cable or microphone cable. Your product was carefully packed at the factory to ensure safe transport. Nevertheless, if the box is damaged inspect the unit immediately for signs of damage.
Ensure adequate air supply and to avoid overheating do not place the unit near radiators etc. For your own safety, never remove or disable the ground conductors from the devices or on the power cords. The unit must always be connected to the mains outlet with a protective grounding connection. Increase the distance between the transmitter and the unit, and use shielded cables for all connections.
Note—after powering off we recommend that the amplifier is allowed to cool down for ten minutes before any attempt is made to move the amplifier. This reduces the risk of mechanical damage to the sensitive valve elements. Introduction Congratulations! BUGERA instrument amplifiers are handmade under stringent production guidelines to ensure long life and reliability. Each one includes our classic valve electronics, hard-wearing switches and potentiometers, high-quality transformers and, not to forget, our hand-selected, precision-matched BUGERA valves.
And, owing to their careful construction and component assembly, they are able to stand up to the toughest demands. To arrange for warranty service, please contact the retailer from whom the equipment was purchased.
Registering your purchase and equipment with us helps us process your repair claims quicker and more efficiently. Thank you for your cooperation! Make sure you select a suitable volume at all times.
This way the amp is idle, but the operational temperature of the valves is maintained POWER switch turned on. When the switch is set to its ON position the amplifier is activated.
This emphasizes the high end and makes the sound crisper. Please make sure that a cable has been connected before turning on the amplifier. Risk of injury! Avoid touching the controls and connectors on the rear panel during use. To avoid accidental contact with hot surfaces, place the rear panel so that it faces a wall.
Turning the knob to the right increases the signal level, whereas turning it to the left decreases the signal level. In order to produce sound with the least possible noise, we suggest using a high setting without distorting the signal.
This signal is specially filtered to provide the optimum signal quality for this application. Always apply the value that is identical to the impedance of the used speaker cabinet. The FUSE is found in the fuse holder. If the fuse is blown, it needs to be replaced with a fuse of the same kind by all means.
Otherwise, the unit could seriously be damaged, in which case the warranty is void. If the fuse is blown repeatedly, you should take the unit to a qualified service technician. At all times, make the connections to the amplifier before plugging the cable into a power outlet. The minimum impedance is 4 Ohms. High voltage! The parts inside the amplifier operate at high voltages and high temperatures. If you want to connect two speaker cabinets, both cabinets should have to the same impedance.
In this case, set it to half the value of one of the cabinets. When using two Ohm cabinets, the switch therefore needs to be set to 8 Ohms; and with two 8-Ohm cabinets, set it to the minimum impedance of 4 Ohms.
When you use two speaker boxes with differing impedance values, the speaker with the lower impedance will provide the highest output power. Make sure that the voltmeter is set to direct current DC. You should always use sets of four matched valves. During use, the valves will get very hot and high surface temperatures may be reached at the rear of this unit. The speaker signal of the connected loudspeaker is picked up by a microphone and is fed to the mixer via a mic input.
This way you get a second guitar signal that is amplified over a PA system or can be recorded additionally or both. As a result of these efforts, modifications may be made from time to time to existing products without prior notice. Specifications and appearance may differ from those listed or illustrated. The limited warranty regulations mentioned herein are applicable unless they constitute an infringement of national warranty law. BEHRINGER warrants valves tubes and meters contained in the product to be free of defects in material and workmanship if used under normal operating conditions for a period of 90 days from the original date of purchase.
This limited warranty is subject to the conditions, exclusions and limitations hereinafter set forth. If the warranty claim proves to be justified, the product will be returned to the user freight prepaid. Warranty claims other than those indicated above are expressly excluded. All inquiries must be accompanied by a description of the problem. The buyer or his authorized dealer will receive a return authorization number 2. Subsequently, the product must be returned in its original shipping carton, together with the return authorization number.
Shipments without freight prepaid will not be accepted. Any repair or opening of the unit carried out by unauthorized personnel user included will void this limited warranty. If an inspection of the product by BEHRINGER shows that the defect in question is not covered by this limited warranty, the inspection costs are payable by the customer. Costs for freight and packing will be invoiced separately C.
When the buyer has sent in a written repair order, such costs will also be invoiced separately. Any implied warranties, including without limitation, any implied warranties of merchantability or fitness for any particular purpose, imposed under state law are limited to the duration of this limited warranty. Some states do not allow limitations on how long an implied warranty lasts, so the above limitations may not be applicable to you.
Technical specifications and appearance are subject to change without notice. The information contained herein is correct at the time of printing. Colors and specifications may vary slightly from product. Our Products are sold through authorized dealers only. This manual is copyrighted. Trident Chambers, Wickhams Cay, P. Related documents.
Bugera 6260 Manuals
Risk of death! High voltages of up to V DC may be present inside the casing for long periods after being disconnected from the mains. To avoid lethal electric shock, do not open the casing. There are no user-serviceable components inside. Refer all maintenance to qualified service personnel. Remove the mains cable when the unit is not in use. WARNING: To eliminate the risk of fire and electric shock, do not expose this unit to rain or moisture and splashing or dripping liquid, which might enter the device.
This document was uploaded by user and they confirmed that they have the permission to share it. If you are author or own the copyright of this book, please report to us by using this DMCA report form. Report DMCA. Home current Explore. Words: 3, Pages: