General search Products Price Download Supply. Product catalogues. Master slave station products. Security products. Control equipments.

Author:Akinozahn Merisar
Language:English (Spanish)
Published (Last):16 May 2008
PDF File Size:8.40 Mb
ePub File Size:19.6 Mb
Price:Free* [*Free Regsitration Required]

All rights reserved. Please refer to Ordering Information when ordering. Platinum resistance thermometer See note 2. Note: 1. The following exceptions apply to thermocouples.

Input set values 0, 1, 2, 3 for E5CSV: 0. Input set value 1 for E5CSV: 0. The voltage output 12 VDC, 21 mA is not electrically isolated from the internal circuits.

Otherwise, unwanted current paths will cause measurement errors. Models using 24 VDC have no polarity. The number of alarm outputs depends on the model. While pushing the E5CSV into place, push 1.

Protect switch 2. Be sure not to impose excessive force on the panel. The alarm mode switch is not provided on models without alarms. Alarm 2 is always set to the upper limit in models with two alarms. A setting switch is not provided for alarm 2. If unit is changed to 1 degree when the SP and alarm value for temperature range. If the input is within the control The default is 3.

All switches are OFF for the default settings. The default is 2. No alarm. For details on the position of the temperature range switch, control mode switches, and alarm mode switch, refer to page 6.

Set the control period. Flashing stops when AT is completed. Note: One of the deviation indicators will flash. To disable input shift, set the input shift value to h0. Mounting the E5CSV 1. For waterproof mounting, waterproof packing must be installed on the Controller.

Insert the E5CSV into the mounting hole in the panel. Push the adapter from the terminals up to the panel, and temporarily fasten the E5CSV. Tighten the two fastening screws on the adapter. Alternately tighten the two screws little by little to maintain a balance. Be sure to remove the cause of the error promptly.

Turn the power ON again. The suffix "W" is added to models with a light gray case color. The ALM2 display has been added. The control method has been changed to 2-PID control. An auto-tuning AT function has been added. The deviation display flashes during self-tuning ST and auto-tuning AT. The control calculation period has been improved from 2 s to 0. External Dimensions The depth has been shortened from mm to 76 mm. The recommended panel thickness is 1 to 4 mm. Group mounting is possible in one direction only.

Do not touch the terminals while power is being supplied. Otherwise, minor injury from explosion may occasionally occur. The product is designed for indoor use only. Never disassemble, modify, or repair the product or touch any of the internal parts. Control Equipment. See note 1.

See note 2. In such a case, use forced cooling by fans or expectancy. To allow heat to escape, do not block the area around the product. Loose screws may occasionally result in fire. Do not block the ventilation holes on the product. Tighten terminal screws to the specified torque of 0. Use the specified size M3. Be sure to wire properly with correct polarity of terminals. OFF before changing any switch setting. Do not wire the terminals that are not used. To avoid inductive noise, keep the wiring for the Temperature Con- prevent alarm outputs, resulting in property damage.

Use the product within the rated load and power supply. Precautions for Correct Use Design the system e. Component A switch or circuit breaker should be provided close to this unit. If the Controller to increase, possibly resulting in fire.

Waterproofing Static electricity may damage internal components. Do not use paint thinner or similar chemical to clean with. Use tools when separating parts for disposal. In no event shall the responsibility of OMRON for any act exceed the individual price of the product on which liability is asserted.

Take all necessary steps to determine the suitability of the product for the systems, machines, and equipment with which it will be used. Know and observe all prohibitions of use applicable to this product. It may represent the result of OMRON's test conditions, and the users must correlate it to actual application requirements.

Consult with your OMRON representative at any time to confirm actual specifications of purchased product. Offer; Acceptance. Prices; Payment Terms. Governmental Approvals. Limitation on Liability; Etc. Property; Confidentiality. Notwithstanding any 9.

Cancellation; Etc. All information and materials supplied Force Majeure. Export Controls. Shipping; Delivery. Omron disclaims all other warranties, express or implied. Suitability of Use. Programmable Products. Performance Data. Change in Specifications. Please know and observe all prohibitions of use applicable to this Product. Errors and Omissions. To convert millimeters into inches, multiply by 0. To convert grams into ounces, multiply by 0.


E5CSV-R1KJ-W AC100-240

All rights reserved. Please refer to Ordering Information when ordering. Platinum resistance thermometer See note 2. Note: 1. The following exceptions apply to thermocouples.


Omron Digital Temperature Controller

A wide variety of standard and configurable components for factory automation engineers in industries such as automotive, semiconductor, packaging, medical and many more. A good selection of accessories such as screws, bolts, washers and nuts that you may need for your daily engineering usage. Browse industrial materials ranging from heat insulating plates, sponges, to metal and plastic materials in different sizes to meet your various applications. A wide variety of wiring parts for connecting and protecting control and PC parts including Connectors, Cables, Electric Wires, Crimping Terminals and more.


E5CSV Controllers. Datasheet pdf. Equivalent



E5CSV-R1KJ-W | OMRON Temperature Controllers E5CSV-R1KJ-W


Related Articles